Guardian Angel Window Guards can now be used in single/double hung windows and in casement/sliding windows. Double hung windows are windows that open up and down. Guardian Angel window guards for double hung windows run horizontally and are measured in width. The bars telescope to fit various window widths. For example, the 2335 model expands to fit a window width from 23 to 35 inches. Owners of casement and sliding windows should not install the Guardian Angel Window Guard with the sliding bars positioned horizontally. A child could use the guard as a ladder and fall through the unguarded area. Casement and sliding window openings must be covered completely, from the bottom to the top of the window opening using vertical mounting of the guards.

Guards are available with different end post sizes as follows:

5 Bars: Length of endpost is 21.75 inches. Maximum window opening is 26 inches

There are 6 widths available, see chart below. If your window width falls right on the edge of a range, it is better to go with the guard in the larger width range. For example, if the width you want to cover is 23 inches, go with the 23 to 35 inch model (2335-xx).

Window Width (inches)	Model No.
14-17	1417-xx
17-23	1723-xx
23-35	2335-xx
35-58	3558-xx
58-90	5890-xx
90-120	7320-xx

Designed to conform to the safety standards for window fall prevention devices set forth by the American Society for Testing and Materials (ASTM F2090-01a), and recognized by the U.S. Consumer Products and Safety Commission.

End posts screw into window frame or molding from sides or front (4 screws per guard)

Never mount telescoping bars horizontally in a sliding or casement window!

CASEMENT AND SLIDER WINDOW GUARDS



You may need more than one guard to cover the width of your window. The vertical window guards can be installed next to each other.

Guards come with 3, 4, or 5 vertical bars and these bars telescope to fit various window heights. The examples following are the 3558 model, which expands from 35 to 58 inches high.

The last two digits in the model number stand for the number of emergency release buttons and number of bars, respectively. For example, the 3558-43 model expands 35 to 58 inches in height, has 4 emergency release buttons and three bars.

There are 6 heights available, see chart below. If your window height falls right on the edge of a range, it is better to go with the larger height range. For example, if the height you want to cover is 23 inches, go with the 23 to 35 inch model.

Designed to conform to the safety standards for window fall prevention devices set forth by the American Society for Testing and Materials (ASTM F2090-01a), and recognized by the U.S. Consumer Products and Safety Commission.

Window Height (inches)	Model No.
14-17	1417-43 (width of end post 13 inches) 1417-44 (width of end post 17.375 inches) 1417-45 (width of end post 21.75 inches)
17-23	1723-43 (width of end post 13 inches) 1723-44 (width of end post 17.375 inches) 1723-45 (width of end post 21.75 inches)
23-35	2335-43 (width of end post 13 inches) 2335-44 (width of end post 17.375 inches) 2335-45 (width of end post 21.75 inches)
35-58	3558-43 (width of end post 13 inches) 3558-44 (width of end post 17.375 inches) 3558-45 (width of end post 21.75 inches)
58-90	5890-43 (width of end post 13 inches) 5890-44 (width of end post 17.375 inches) 5890-45V (width of end post 21.75 inches)
90-120	7320-43 (width of end post 13 inches) 7320-44 (width of end post 17.375 inches) 7320-45 (width of end post 21.75 inches)

Never mount telescoping bars horizontally in a sliding or casement window!

Telescoping bars can only be mounted horizontally in double-hung windows. When mounted horizontally in sliding and casement windows, the window guard can act as a ladder and greatly increase the risk of an accidental window fall.

For casement and sliding windows, guards must be mounted with the telescoping bars in a vertical position. Refer to installation instructions and specifications below for these types of windows.

End post screws into bottom of window frame or molding from top or front (4 screws per guard)

End post screws into bottom of window frame or molding from top or front (4 screws per guard)